- #Cisco asa compatible ipsec vpn client windows 10 install
- #Cisco asa compatible ipsec vpn client windows 10 windows 10
- #Cisco asa compatible ipsec vpn client windows 10 windows 7
But I have to figure out as customer now has mainly windows 10 laptops.
#Cisco asa compatible ipsec vpn client windows 10 windows 7
Just occurred to me and I installed VPN client on windows 7 laptop and tested with that and I don't have these issues anymore. I get these intermittent and unexplained issues with VPN connectivity as described above. I was testing with windows 10 with VPN client and second laptop I have is windows 7. I have opened the case with support and they are looking into it. And again played with the SA timings and things again break down. Did reboots again, and with no change.ĭeleted configuration and re-created the same config and it worked. Changed SA lifetime back to 3600 at both sides and still no luck. Then I changed the SA lifetime back to defaults and I found that pings stopped working. Did both ends reboot again to make sure my VPN is still working. Then I added the matching ID as remote ID in firewall IKE policy and disconnected and reconnected and traffic flowed fine again. Remember client end will always need to have a local ID, which I set up just a name. So I thought somehow SA lifetime has some quirks.ĭid a reboot of the firewall and the client laptop and I was able to get VPN work after these reboots. I then changed phase 2 / IPsec policy lifetime to be 1 hr from default 8 hours (28800 does not show up in CLI being default) and that made the whole thing work. So first I added a test user, then added a aaa authentication login list and used that list name under the IKE policy for client authentication and then changed shrewsoft Authentication tab to Mutual PSK+XAUTH and tried again. Despite both end configuration to be correct, and tunnel establishing, the traffic will not flow. I had no user authentication (XAUTH) and I was keeping remote-id to be any, so that any client that dials in using PSK will connect with the intention to add on XAUTH as a next step and then also add a matching remote-id in the firewall.
I was trying to first keep the things simple. Success rate is 100 percent (5/5), round-trip min/avg/max = 0/0/1 msĢ current IPv4 + IPv6 IPsec SAs on all VRFs (2 peak of 4000 max) Sending 5, 100-byte ICMP Echos to 192.168.110.1, timeout is 2 seconds: 'x' = TTL expired in transit, 'e' = Unknown error '*' = Request timed out, '-' = Destination host unreachable Legend: '!' = Success, '?' = Unknown host, '$' = Invalid host address Ip crypto ipsec transform-set VPNTS esp-aes-128-cbc esp-sha-hmacĬrypto ike remote-id any preshared-key labtest1234567890 ike-policy 100 crypto map VPN 10 no-xauth Nat source list InternetBoundTraffic interface gigabit-ethernet 0/1 overloadĪllow reverse list VPN_USERS_ACCESS stateless Please review and advise if I am doing something fundamentally wrong.Ĭrypto ike client configuration pool VPN_USERS Here is the relevant lab setup configuration.and some outputs. Show crypto ike sa and show ip crypto ipsec sa, all show expected outputs, however no traffic passes (TX and RX are shown 0 bytes) from the VPN client to the inside private network.
#Cisco asa compatible ipsec vpn client windows 10 install
The tunnel forms successfully, the VPN client and the windows laptop show install of route to the VPN subnets behind the firewall, thru the VPN virtual adapter. Just tried to setup a quick remote access VPN using Shrewsoft VPN client on a 3140 running NV3140A-R12-2-0-E and I am running into issues. I am new to Netvanta routers / firewalls.
0 kommentar(er)
